Wand met StarTec

De StarTec wandbekisting is onze sterke universele bekisting tot een hoogte van 3,30 m. Zij is 100 % compatibel met de lichte handbekisting AluStar.

Verder onderaan op deze pagina vindt u de artikelen die u nodig heeft als u een wand met StarTec wilt bekisten. Denk er aan dat het aantal artikelen voor elk bouwproject kan verschillen. Gebruik het formulier en neem even contact met ons op als u exact wilt weten hoeveel onderdelen u nodig heeft.

Op de productpagina vindt u alles over onze universele wandbekisting StarTec.

Downloads voor StarTec wandbekisting

Geen noteringen beschikbaar

Contactformulier

 
 
 

Of neem rechtstreeks contact met ons op.

 

Artikellijst

 
 
Bekisting
Verankering
Ondersteuning
Veiligheid
 
 
  • ST panels

    Construction height 12 cm, frame profile width 4 cm. Three tie holes per panel height 330 cm, two tie holes per panel height... 

  • ST panel 270/45 with concreting window

    Is used to control the pouring process when control is not possible from above. 

  • ST panel AL 17, 270/45 with filling nozzle

    Is used when concrete cannot be poured from above, e.g. tunnel formwork. Connection with a manual gate valve. Operating... 

  • ST inside corner

    For 90° corners. Side length 25 cm. Steel frame with tie holes and alkus facing or exchangeable steel sheet. 

  • AS/ST outside corner

    Aluminium. Provides together with ST panels and AS assembly locks a fast and stable outside corner assembly for 90° angles. 

  • AS hinged inside corner

    Steel construction with steel sheeting. Side length 30 cm. Adjustable angle 60°-180°. 

  • AS hinged outside corner

    Steel construction with steel sheeting. Side length 7,5 cm. Adjustable angle 60°-180°. 

  • ST stripping corner

    Steel construction with steel sheeting. Side length 25 cm. With tie holes. When the bell-crank lever is pushed upwards with... 

  • Stripping support

    The stripping support is used to easily activate the stripping corner from above. Use a power screwdriver, a ratchet wrench... 

  • AS assembly lock

    Galvanized. Tightly connects and aligns AluStar and StarTec panels. Clamping length 8 cm.  

  • Uni-assembly lock

    Galvanized. For stepless compensation. Clamping length 22 cm or 28 cm. 

  • Combi-lock with coupling

    Galvanized. Is used to attach the push-pull props at the panel joint of the wall formwork AluStar, StarTec, Mammut and... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • ST aluminium filler

    Aluminium with high-quality annealed powder coating. With tie holes. For length compensation of 5 cm, especially in corners.... 

  • ST compensation plate

    Steel construction with steel sheeting. Is used to compensate gaps of 8 to 20 cm and attached to the panel with 2 assembly... 

  • AS timber profile

    Timber profile with groove. To support job-built fillers of 14 cm or more or to connect job-built formwork with 21 mm... 

  • Alignment rail

    Galvanized. Is used to brace panel joints for crane ganging, bridge problem areas, brace compensation areas and build stop... 

  • Stop end bracket

    Galvanized. Is used to form stop ends. Suitable for frame profile widths 23 mm (EcoAs, AluFix), 40 mm (AluStar, StarTec)... 

  • Uni-tie claw

    Galvanized. Permits tieing directly above or beside the panels. Is suited for panels with a frame profile width of 40 mm... 

  • Stop end fixture 23/40 yellow

    Yellow chromated. Is used to attach alignment rails to the panels when forming stop ends are formed. Or is used in... 

  • Door spindle MFS

    Steel, galvanized, DW 20. Adjustment range 700-1100 mm. Is used to brace door and window blockouts. With nail holes.... 

  • AS crane hook

    Is used to move panels. Self-locking. Load capacity: 15 kN (1,5 tons). Always 2 crane hooks required per gang. For use and... 

  • MevaTrenn pro

    Not shown. Suited for absorbent and non-absorbent forming faces.Solvent-based. Evaporates when applied, leaving avery thin... 

  • Sprayer

    Not shown. To allow for an even and sparing spraying of the forming surface, suited for (5 litre) MevaTrenn and wax. 

  • Concrete scraper

    With 6 or 10 replaceable hard-metal plates and steel ledge. Wooden stick (ash-tree) with handle. 

  • Beam clamp H20/H20

    Galvanized. Is used to attach planks or cross beams to H20 beams when using slab tables. 

  • Safety bolt

    Secures stacked panels. 

  • Transport angle 12

    Is used to stack and transport 5 to 12 frame formwork panels with a construction height of 12 cm and 12 cm hole distance.... 

 
 
  • Articulated flange nut 15/120

    Forged, galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 120 mm, max. inclination 10°, SW 27. Max. load capacity 90 kN.... 

  • Flange nut 100

    Forged, galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 100 mm, SW 27. Admissible load 90 kN. 

  • Spanner SW 27

    Inset yellow chromated. Spanner width (SW) 27 mm. Is used to tighten and loosen flange nuts 100, articulated flange nuts... 

  • Drive nut 60

    Galvanized. DIN 18216. DW thread Ø 15mm, plate Ø 60 mm. Adm. load capacity 90 kN. Is used to anchor the formwork to the... 

  • Tie rod DW 15/90

    Uncoated, not weldable. DW thread Ø 15 mm. Is used to tie panels of double-sided formwork. Adm. load capacity 90 kN (DIN... 

  • Pressure gauge

    Not shown. Measures tractive force of anchors from 250 to 400 kN. Includes compensating plate for tie rods, with 50 mm hole... 

  • Plug D20

    Is used to close unused tie holes (AluFix, EcoAs, AluStar and StarTec). 

  • Stop end bracket

    Galvanized. Is used to form stop ends. Suitable for frame profile widths 23 mm (EcoAs, AluFix), 40 mm (AluStar, StarTec)... 

  • Cone for plastic tube

    Available with 10 mm or 30 mm covering . 

  • Plug

    Is used to close tie holes in the wall when plastic tubes D22 or D30 are applied. Two plugs are required per tie hole.  

  • Water stop

    Uncoated. Lost part for tie rods DW 15 and DW 20 to produce watertight tie holes. Adm. load capacity depends on diameter: Ø... 

  • Uni-tie claw

    Galvanized. Permits tieing directly above or beside the panels. Is suited for panels with a frame profile width of 40 mm... 

  • Tensioner AS/ST for foundation tape

    Galvanized. Connects the foundation tape to AluStar or StarTec panels and serves as bottom anchoring when panels are... 

  • Trolley for foundation tape

    Not shown. Is used to transport and cut foundation tapes to length. Suitable for one roll Pneumatic wheels. 

  • Pressure gauge

    Not shown. Measures tractive force of anchors from 250 to 400 kN. Includes compensating plate for tie rods, with 50 mm hole... 

 
 
  • Side railing

    Galvanized. Is plugged into the walkway bracket. 

  • Push-pull prop R

    Galvanized. Garantee tensile and compression strength. Align and brace wall formwork. Foot plates and... 

  • Braces SRL

    Galvanized. Guarantee tensile and compression strength. With right-hand and left-hand spindle and revolving centre part.... 

  • Brace frame 250

    Galvanized. Aligns and braces the formwork. Available with or without formwork-prop connector. Consists of a push-pull prop... 

  • Ladder

    Galvanized. Is hooked into the CF-access platform and automatically secured. Can be extended with extension ladders. Safety... 

  • Formwork-prop connector

    Galvanized. Connects braces, brace frames and push-pull props (max. Ø 48 mm) to the multi-function profile (with a flange... 

  • Universal joint connector 76/135

    Galvanized. With head bolt 16/90 and cotter pin 4. Is used to attach push-pull props to vertical or horizontal panel joints... 

  • Articulated foot plate

    Galvanized. With head bolt 16/90 and cotter pin 4. For push-pull props and braces of up to Ø 57 mm. 

  • Double-jointed foot plate

    Galvanized. With head bolt 16/90 and cotter pin 4. Serves as foot plate for brace frames 250 and as connector for braces and... 

  • Formwork-prop connector

    Galvanized. Is used to connect braces, brace frames and push-pull props (max. Ø 48,3 mm) to the multi-function profile with... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • Triplex R

    Galvanized. Braces and aligns wall and column formwork exceeding 6,00 m. Is delivered in modules and assembled on site to... 

  • Triplex intermediate pieces R

    Galvanized basic components of different lengths to build Triplex R units. Tube Ø 33,7 mm. Delivery includes the required... 

  • Top unit 48

    Galvanized. With adjustable spindle (Ø 48,3 mm). 1 top unit 48 left and 1 top unit 48 right are required to assemble a... 

  • Foot plate 48

    Galvanized. Particularly solid foot plate for braces up to Ø 48,3 mm such as Triplex R. Delivery includes head bolt 16/90... 

  • Triplex SB

    Galvanized. Triplex SB braces are primarily used for additional load transfer when forming single-sided walls of 6,00 m or... 

  • Foot plate 73

    Galvanized. Particularly sturdy foot plate for Triplex SB. Delivery includes screw M30x150 and nut M30. 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • Combi-lock with coupling

    Galvanized. Is used to attach push-pull props at the panel joints of AluStar, StarTec, Mammut and Mammut 350 wall formwork.... 

Vanaf een storthoogte van 2 m dient er altijd een een vierdelige zijdelingse bescherming aan het stortplatform te worden aangebracht.

Met de MEVA veiligheidssysteem kunt u uw bouwterrein modulair en individueel beveiligen. Kijk voor meer informatie op de Veiligheidssystemen pagina en neem voor voor advies contact op met MEVA.

  • Guard-railing post

    Galvanized. Is plugged into the walkway bracket. 

  • Guard-railing post 48

    Galvanized. With manifold to attach it to the walkway bracket, designed with tube Ø 48 mm to attach tube couplers. 

  • Support guard 800-railing post

    Galvanized. For the side protection at all MEVA wall formwork systems. Allows the extension for guard-railing KLK 230 and... 

  • Scaffold tube

    Galvanized. Is used as hand-rail / mid-rail in combination with guard-railing post 48. 

  • Plastic tube

    Is used as a plastic sleeve for a tie rod that is to be recovered and re-used. 2 m long.  

  • Planing cap DW

    Hard foam, 10 cm long, 45° end piece. For DW 15 and DW 20. Is plugged onto the DW tie rod or on a plastic sleeve for... 

  • Spiral anchor DW 15/100

    Steel spiral bead, 10 cm long, with styropore core. Is used to attach formwork equipment with tie rods DW 15, e.g. when... 

  • Folding access platform BKB 125

    Self-locking; ready-made platform with a foldable guard-railing and an overall width of 125 cm; it is supsended onto the... 

  • Folding access platform BKB 125/140

    It is used for inside corner configurations and length adjustments. In the latter case a side railing BKB 125 and two (2)... 

  • Side railing BKB 125

    Galvanized. Suited as side railing for all folding access platforms or as guard-railing for platform BKB 125/140. Is... 

  • Walkway bracket

    Galvanized, yellow, pluggable. Is used as a working and safety scaffold. Is attached to the multi-function profile and... 

  • Side railing

    Galvanized. Is plugged into the walkway bracket. 

  • Walkway bracket SB

    Galvanized. Is attached with 1 flange screw 28 and 1 flange screw 18 to the DW-threaded nuts of the panel’s multi-function... 

  • Walkway bracket 880 SB

    Galvanized. Is attached with 1 flange screw 28 and 1 flange screw 18 to the DW-threaded nuts of the panel’s multi-function... 

  • Alu(minium) platform ST SB

    Aluminium support construction with slip-free corrugated aluminium sheet. Working width 75 cm. Admissible load 200 kg/m².... 

  • Alu(minium) platform ST 2370 SB with hatch

    Aluminium support construction with slip-free corrugated aluminium sheet. Working width 75 cm. Admissible load 200 kg/m².... 

  • Alu platform outside corners SB

    Aluminium support construction with slip-free corrugated aluminium sheet. Is placed onto 2 Walkway brackets SB and on the... 

  • Protection bracket SB

    The protection bracket SB is plugged into the aluminium platform and attached to the wooden compensation platform with two... 

  • Compensation sheet

    Bridges gaps up to 135 cm of 75 cm wide. 

  • Compensation covering 570 plugable

    Pluggable. Bridges gaps up to 40 cm wide. 

  • Front guard-railing post SB 10

    Not shown. Galvanized. Is used together with a scaffold tube to create a handrail. The front guard-railing post SB 10 is... 

  • Front railing post SB retractable

    Galvanized, dia. 48.3 mm. Is used to install a retractable front railing SB made of scaffold tubes. On the facing side of... 

  • Support railing post SB, retractable

    Galvanized. Is used for the retractable front railing SB made of scaffold tubes. The support is attached to the walkway... 

  • Support for guard-railing post IC SB

    Galvanized. Is used for the attachment of a front guard-railing post. Is attached to the multi-function profile of the wall... 

  • Support for guard-railing post OC SB

    Galvanized. Is placed onto 2 Walkway brackets SB and secured to the Alu platform outside corners SB with the integrated pin. 

  • Scaffold tube SB

    Galvanized. Is used to assemble front railings for SecuritBasic aluminium platforms.  

  • Swivel-joint coupler 48/48

    Galvanized. Connects 2 scaffold tubes with 48,3 mm Ø at any angle.