Contactformulier

Frame profile height 10 cm, frame profile width 23 mm. Three tie holes per panel heights 300 cm and 240 cm, two tie holes per panel heights 160 cm and 120 cm. Heights 240 cm, 160 cm and 120 cm: centered tie hole at the top and bottom for horizontal application. The frames of EA panels are made of closed steel profiles and are torsion proof. Thanks to their high-quality annealed powder coating, priming and cavity sealing they are corrosion-resistant and easy to clean. EA panels are equipped with alkus AL 17 all plastic facing or, alternatively, with a coated multi-layer plywood facing (15 mm). All around grooves and EA assembly locks guarantee a tight and perfectly aligned stepless panel connection. Conical anchor sleeves are weld into the frames. Multi function profiles allow for an easy, fast and safe attachment of accessories.

Completely made of steel, primed and cavity-sealed, with tie holes. For length adjustment of 5 cm, particularly in corners. For the required quantity of Uni-assembly locks see Technical Instruction Manual EcoAs.

Steel construction with steel sheeting, primed and cavity-sealed. Is used to compensate gaps of 6 to 20 cm and attached to panels with 2 EA assembly locks. Alignment rails must be used to bridge and align the panels with the compensation plate.

Aluminium frame with high-quality annealed plastic coating. All-plastic facing. Aluminium frame with tie holes. For 90° corners, side length 25 cm.

Aluminium with high-quality annealed plastic coating. Facing 5 cm wide on both sides, integrated chamfer strip. Provides together with EA panels and EA assembly locks a fast and tight outside corner assembly for 90° angles.

Steel construction with steel sheeting, primed and cavity-sealed. Side length 30 cm. Adjustable angle 60° to 180°.

Steel construction with steel sheeting, primed and cavity-sealed. Side length 7,5 cm. Adjustable angle 60° to 180°.

Galvanized. Tightly connects and aligns AluFix and EcoAs panels. Clamping length 4,6 cm. Three assembly locks are required per panel joint for a panel height of 3,00 m and two assembly locks per panel joint for a panel height of 2,64 m or 1,32 m.

Galvanized. For stepless compensation. Clamping length 22 cm or 28 cm.

Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc. Length of thread 18 cm or 27 cm.

10 cm wide, 120 cm high. Diagonally divided timber filler. Permits easy stripping in restricted areas such as shafts and staircases. Two Uni-assembly locks are required per dismantling auxiliary. Alignment rails must be used for reinforcement. Delivery and weight by pairs.

Galvanized. Is used to brace panel joints for crane ganging, bridge problem areas, brace compensation areas and build stop ends with stop end fixtures. Is attached to the formwork with flange screws.

Galvanized. Side lengths 40 cm and 60 cm. For inside and outside corners and column formwork.

Coated. Is used to move and crane-gang AluFix and EcoAs panels. Self-locking. Load capacity 6 kN (600 kg). Always two crane hooks required per gang. Refer to the crane hook Operating Instructions for application and safety test.

Is used to stack and transport 5 to 12 EcoAs or AluFix panels. Distance between holes 10 cm. We recommend using 2 foldable angles and 2 angles of the rigid type per stack. Max. load capacity is 10 kN per angle. For safety reasons consider 20 kN as maximum capacity for the whole stack.

Plastic, black. Secures stacked AluFix, Ecos, AluStar and StarTec panels.

Forged, galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 120 mm, max. inclination 10°, SW 27. Max. load capacity 90 kN. Reduces wear of panel coating.

Forged, galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 100 mm, SW 27. Admissible load 90 kN.

Inset yellow chromated. Spanner width (SW) 27 mm. Is used to tighten and loosen flange nuts 100, articulated flange nuts 15/120 and flange screws.

Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc. Length of thread 18 cm or 27 cm.

Galvanized. DW thread Ø 15 mm, plate Ø 60 mm. Adm. load capacity 90 kN (DIN 18216). Is used to tie the formwork to the ground or to a wall connection.

Uncoated, not weldable. DW thread Ø 15 mm. Adm. load capacity 90 kN (DIN 18216). Is used to tie panels of a double-sided formwork.

Galvanized. Permits tieing (with tie rod DW 15 and flange nut 100) directly above or beside EcoAs and AluFix panels.

Not shown. Measures tractive force of anchors from 250 to 400 kN. Includes compensating plate for tie rods, with 50 mm hole diameter.

Galvanized. Hole spacing 50 mm, hole Ø 16 mm, length 50 m. Adm. tractive force 10 kN. To be cut at hole center. Serves together with the appropriate tensioner as bottom anchoring when assembling panels in horizontal position.

Not shown. Is used to transport and cut foundation tapes to length. Suitable for one roll Pneumatic wheels.

Galvanized. Connects the foundation tape to EcoAs or AluFix-panels and serves as bottom tie when panels are assembled in horizontal position. Two tensioners are required per tieing position.

Is used to close unused tie holes (AluFix, EcoAs, AluStar and StarTec).

Galvanized. Is used to form stop ends and suited for frame formwork panels with a profile width of 23 mm (EcoAs, AluFix), 40 mm (StarTec, AluStar) and 60 mm (Mammut, Mammut 350).

Available with 10 mm or 30 mm covering .

Is used to close tie holes in the wall when plastic tubes D22 or D30 are applied. Two plugs are required per tie hole.

Uncoated. Lost part for tie rods DW 15 and DW 20 to produce watertight tie holes. Adm. load capacity depends on diameter: Ø 15 mm (90 kN), Ø 20 mm (150 kN).

Yellow chromated. Is used to attach alignment rails to the panels when forming stop ends are formed. Or is used in connection with multi-purpose panels (EcoAs, StarTec) to form outer corners or abutments. Suited for the frame profiles of EcoAs and AluFix (23 mm) and AluStar/StarTec (40 mm). A flange nut 100 or an articulated flange nut 15/120 are required in addition.

Not shown. Is used to remove the ground nail from the earth together with a lever rod (not supplied).

Galvanized. Is hooked into the CF-access platform and automatically secured. Can be extended with extension ladders. Safety cages are required for operational safety.

Galvanized. Garantee tensile and compression strength. Align and brace wall formwork. Foot plates and formwork-prop-connectors to be ordered separately.

Galvanized. Guarantee tensile and compression strength. With right-hand and left-hand spindle and revolving centre part. Align and brace wall formwork. Foot plates and formwork-prop-connectors to be ordered separately.

Galvanized. Aligns and braces the formwork. Available with or without formwork-prop connector. Consists of a push-pull prop R 250 (190-320cm), a brace SRL 120 (90-150cm) and a double-jointed footplate. The formwork-prop connectors are attached to the formwork with flange screws 18.

Galvanized. Connects braces, brace frames and push-pull props (max. Ø 48 mm) to the multi-function profile (with a flange screw 18). Delivery includes head bolt 16/90 and cotter pin 4.

Galvanized. Is used to attach push-pull props at the panel joints of AluStar, StarTec, Mammut and Mammut 350 wall formwork. Clamping length 8, 10 and 12 cm.

Galvanized. With head bolt 16/90 and cotter pin 4. Is used to attach push-pull props to vertical or horizontal panel joints A Combi-lock with coupling is also required. Typical application in folding shaft formwork.

Galvanized. With head bolt 16/90 and cotter pin 4. For push-pull props and braces of up to Ø 57 mm.

Galvanized. With head bolt 16/90 and cotter pin 4. Serves as foot plate for brace frames 250 and as connector for braces and push-pull props up to Ø 57 mm.

Galvanized. Is used to connect braces, brace frames and push-pull props (max. Ø 48,3 mm) to the multi-function profile with a flange screw 18. Delivery includes head bolt 16/90 and cotter pin 4.

Galvanized. Locks the head bolt.

Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc. Length of thread 18 cm or 27 cm.

Galvanized, yellow, pluggable. Is used as a working and safety scaffold. Is attached to the multi-function profile and secured to the multi-function profile below with a flange screw 18. The planking can be mounted to the brackets. Working width approx. 90 cm (or 125 cm). Guard-railing post 100 or 140 is required in addition. Bracket spacing depends on the type of planking (according to DIN 4420).

Galvanized. Is plugged into the walkway bracket.

Galvanized. With manifold to be plugged into the walkway bracket and with 48 mm Ø tube to attach scaffold couplers.

Galvanized. For the side protection at all MEVA wall formwork systems. Allows the extension for guard-railing KLK 230 and all MEVA guard-railing posts to be plugged in. Guard-railing posts and flange screws 18 must be ordered separately.

Galvanized. Connects two scaffold tubes with Ø 48,3 mm at any angle.

Is used as a plastic sleeve for a tie rod that is to be recovered and re-used. 2 m long.

Hard foam, 10 cm long, 45° end piece. For DW 15 and DW 20. Is plugged onto the DW tie rod or on a plastic sleeve for one-sided anchoring of support frames STB. Hole depth 5 cm.

Steel spiral bead, 10 cm long, with styropore core. Is used to attach formwork equipment with tie rods DW 15, e.g. when adjusting the equipment when using push-pull props or the like. Remove the styropore with a 14 mm drill.

Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc. Length of thread 18 cm or 27 cm.