Wand met AluFix

Voor het kamerhoog storten in de woningbouw zorgt de AluFix handbekisting voor een niet te evenaren prijs-kwaliteitverhouding. Met haar verzonken greep kan zij ook bij nat weer probleemloos net de hand worden geplaatst.

Verder onderaan op deze pagina vindt u de artikelen die u nodig heeft als u een   wand met AluFix wilt bekisten. Denk er aan dat het aantal artikelen voor elk bouwproject kan verschillen. Gebruik het formulier en neem even contact met ons op als u exact wilt weten hoeveel onderdelen u nodig heeft.

Op de productpagina vindt u alles over de lichte AluFix wand- en vloerbekisting.

Downloads over AluFix

Contactformulier

 
 
 

Of neem rechtstreeks contact met ons op.

 

Artikellijst

 
 
Bekisting
Verankering
Ondersteuning
Sicherheit
 
 
  • AF panels

    Construction height 10 cm, frame profile width 23 mm. Three tie holes per panel height 264 cm and 300 cm, two tie holes per... 

  • AF compensation profile

    Steel frame profile with angles. Primed and cavity-sealed. Is clamped to the AF panel with two E assembly locks and used for... 

  • AF inside corner Alu(minium)

    Aluminium. With annealead power coating. For 90° corners, side length 20 cm. 

  • AF outside corner Alu(minium)

    Aluminium. With annealed powder coating. Provides a tight outside corner assembly for 90° angles when used together with AF... 

  • AF hinged inside corner

    Steel construction with steel sheeting. Primed and cavity-sealed. Side length 20 cm. Adjustable angle 80°-180° when used... 

  • AF hinged outside corner

    Steel construction with steel sheeting. Primed and cavity-sealed. Side length 1,5 cm. Adjustable angle 0°-120°. 

  • Assembly lock

    Galvanized. Tightly connects and aligns AluFix and EcoAs panels. Clamping length 4,6 cm. Three assembly locks are required... 

  • Uni-assembly lock

    Galvanized. For stepless compensation. Clamping length 22 cm or 28 cm. 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • AS alignment rail

    Galvanized. Is used to brace panel joints for crane ganging, bridge problem areas, brace compensation areas and build stop... 

  • Corner bracket 40/60

    Galvanized. Side lengths 40 cm and 60 cm. For inside and outside corners and column formwork. 

  • Door spindle MFS

    Steel, galvanized, DW 20. Adjustment range 700-1100 mm. Is used to brace door and window blockouts. With nail holes.... 

  • Crane hooks

    Coated. Is used to move and crane-gang AluFix and EcoAs panels. Self-locking. Load capacity 6 kN (600 kg). Always two crane... 

  • Transport angle

    Is used to stack and transport 5 to 12 EcoAs or AluFix panels. Distance between holes 10 cm. We recommend using 2 foldable... 

  • AS/ST safety bolt, black

    Plastic, black. Secures stacked AluFix, Ecos, AluStar and StarTec panels. 

  • MevaTrenn pro

    Not shown. Suited for absorbent and non-absorbent forming faces.Solvent-based. Evaporates when applied, leaving avery thin... 

  • Sprayer

    Not shown. To allow for an even and sparing spraying of the forming surface, suited for (5 litre) MevaTrenn and wax. 

  • Concrete scraper

    With 6 or 10 replaceable hard-metal plates and steel ledge. Wooden stick (ash-tree) with handle. 

  • Beam clamp H20/H20

    Galvanized. Is used to attach planks or cross beams to H20 beams when using slab tables. 

 
 
  • Articulated flange nut 15/120

    Forged, galvanized. DIN 18218. DW thread Ø 15 mm, plate Ø 120 mm, max. inclination 10°, SW 27. Max. load capacity 90 kN.... 

  • Flange nut 100

    Forged, galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 100 mm, SW 27. Admissible load 90 kN. 

  • Spanner SW 27

    Inset yellow chromated. Spanner width (SW) 27 mm. Is used to tighten and loosen flange nuts 100, articulated flange nuts... 

  • Drive nut 60

    Galvanized. DW thread Ø 15 mm, plate Ø 60 mm. Adm. load capacity 90 kN (DIN 18216). Is used to tie the formwork to the... 

  • Tie rod DW 15/90

    Uncoated, not weldable. DW thread Ø 15 mm. Adm. load capacity 90 kN (DIN 18216). Is used to tie panels of a double-sided... 

  • Tie claw 23

    Galvanized. Permits tieing (with tie rod DW 15 and flange nut 100) directly above or beside EcoAs and AluFix panels. 

  • Pressure gauge

    Not shown. Measures tractive force of anchors from 250 to 400 kN. Includes compensating plate for tie rods, with 50 mm hole... 

  • Foundation tape

    Galvanized. Hole spacing 50 mm, hole Ø 16 mm, length 50 m. Adm. tractive force 10 kN. To be cut at hole center. Together... 

  • Tensioner EA for foundation tape

    Galvanized. Connects the foundation tape to EcoAs or AluFix-panels and serves as bottom tie when panels are assembled in... 

  • Trolley for foundation tape

    Not shown. Is used to transport and cut foundation tapes to length. Suitable for one roll Pneumatic wheels. 

  • Plug D20

    Is used to close unused tie holes (AluFix, EcoAs, AluStar and StarTec). 

  • Stop end bracket

    Galvanized. Is used to form stop ends and suited for frame formwork panels with a profile width of 23 mm (EcoAs, AluFix), 40... 

  • Cone for plastic tube

    Available with 10 mm or 30 mm covering . 

  • Plug

    Is used to close tie holes in the wall when plastic tubes D22 or D30 are applied. Two plugs are required per tie hole.  

  • Water stop

    Uncoated. Lost part for tie rods DW 15 and DW 20 to produce watertight tie holes. Adm. load capacity depends on diameter: Ø... 

  • Extractor for double-headed ground nail

    Not shown. Is used to remove the ground nail from the earth together with a lever rod (not supplied).  

 
 
  • Push-pull prop R

    Galvanized. Garantee tensile and compression strength. Align and brace wall formwork. Foot plates and... 

  • Ladder

    Galvanized. Is hooked into the CF-access platform and automatically secured. Can be extended with extension ladders. Safety... 

  • Side railing

    Galvanized. Is plugged into the walkway bracket. 

  • Brace frame 250

    Galvanized. Aligns and braces the formwork. Available with or without formwork-prop connector. Consists of a push-pull prop... 

  • Formwork-prop connector

    Galvanized. Connects braces, brace frames and push-pull props (max. Ø 48 mm) to the multi-function profile (with a flange... 

  • Universal joint connector 76/135

    Galvanized. With head bolt 16/90 and cotter pin 4. Is used to attach push-pull props to vertical or horizontal panel joints... 

  • Articulated foot plate

    Galvanized. With head bolt 16/90 and cotter pin 4. For push-pull props and braces of up to Ø 57 mm. 

  • Double-jointed foot plate

    Galvanized. With head bolt 16/90 and cotter pin 4. Serves as foot plate for brace frames 250 and as connector for braces and... 

  • Formwork-prop connector

    Galvanized. Is used to connect braces, brace frames and push-pull props (max. Ø 48,3 mm) to the multi-function profile with... 

  • Cotter pin 4

    Galvanized. Locks the head bolt. 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • Combi-lock with coupling

    Galvanized. Is used to attach push-pull props at the panel joints of AluStar, StarTec, Mammut and Mammut 350 wall formwork.... 

Vanaf een storthoogte van 2 m dient er altijd een een vierdelige zijdelingse bescherming aan het stortplatform te worden aangebracht.

Met de MEVA veiligheidssysteem kunt u uw bouwterrein modulair en individueel beveiligen. Kijk voor meer informatie op de Veiligheidssystemen pagina en neem voor voor advies contact op met MEVA.

  • Walkway bracket

    Galvanized, yellow, pluggable. Is used as a working and safety scaffold. Is attached to the multi-function profile and... 

  • Guard-railing post

    Galvanized. Is plugged into the walkway bracket. 

  • Guard-railing post 48

    Galvanized. With manifold to be plugged into the walkway bracket and with 48 mm Ø tube to attach scaffold couplers.  

  • Side railing

    Galvanized. Is plugged into the walkway bracket. 

  • Support guard 800-railing post

    Galvanized. For the side protection at all MEVA wall formwork systems. Allows the extension for guard-railing KLK 230 and... 

  • Swivel-joint coupler 48/48

    Galvanized. Connects two scaffold tubes with Ø 48,3 mm at any angle. 

  • Plastic tube

    Is used as a plastic sleeve for a tie rod that is to be recovered and re-used. 2 m long.  

  • Planing cap DW

    Hard foam, 10 cm long, 45° end piece. For DW 15 and DW 20. Is plugged onto the DW tie rod or on a plastic sleeve for... 

  • Spiral anchor DW 15/100

    Steel spiral bead, 10 cm long, with styropore core. Is used to attach formwork equipment with tie rods DW 15, e.g. when... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc....