Contactformulier

Construction height 12 cm, frame profile width 4 cm. Three tie holes per panel height 330 cm, two tie holes per panel height 270 cm, one tie hole per panel height 135 cm and 90 cm. Absolutely compatible with AluStar panels. The frames of ST panel frames are made of closed steel profiles and are torsion-proof. ST panels are equipped with alkus AL 20 or AL 17 facing. As an alternative, the panels can be delivered with a multi-layer plywood facing (18 mm or 15 mm). All-around grooves and AS assembly locks guarantee a tight and perfectly aligned stepless panel connection. Conical anchor sleeves are weld into the frames. Multi-function profiles permit an easy, fast and safe attachment of accessories.

Is used to control the pouring process when control is not possible from above.

Is used when concrete cannot be poured from above, e.g. tunnel formwork. Connection with a manual gate valve. Operating pressure: 20 bar.

For 90° corners. Side length 25 cm. Steel frame with tie holes and alkus facing or exchangeable steel sheet.

Aluminium. Provides together with ST panels and AS assembly locks a fast and stable outside corner assembly for 90° angles.

Steel construction with steel sheeting. Side length 30 cm. Adjustable angle 60°-180°.

Steel construction with steel sheeting. Side length 7,5 cm. Adjustable angle 60°-180°.

Galvanized. Tightly connects and aligns AluStar and StarTec panels. Clamping length 8 cm.

Galvanized. For stepless compensation. Clamping length 22 cm or 28 cm.

Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc. Length of thread 18 cm or 27 cm.

Aluminium with high-quality annealed powder coating. With tie holes. For length compensation of 5 cm, especially in corners. 2 or 3 Uni-assembly locks are required for each filler.

Steel construction with steel sheeting. Is used to compensate gaps of 8 to 20 cm and attached to the panel with 2 assembly locks. Alignment rails must be used to bridge and align the panels with the compensation plate.

Timber profile with groove. To support job-built fillers of 14 cm or more or to connect job-built formwork with 21 mm forming face; is attached to the AS/ST-panels with 2 AS-assembly locks. Delivery and weight by pairs.

Coated. Links formwork in vertical position and support frames with flange screws. Allows to build transport units. Welded-in nuts guarantee a support frame spacing adapted to MEVA wall formwork systems.

Galvanized. In connection with support frames STB 300 it is used as a tie-beam to transfer the load from the support frame into the anchoring loops.

Is used to move panels. Self-locking. Load capacity: 15 kN (1,5 tons). Always 2 crane hooks required per gang. For use and safety check see the Operating Instructions.

Is used to stack and transport 5 to 12 frame formwork panels with a construction height of 12 cm and 12 cm hole distance. Max. load capacity is 10 kN per angle. For safety reasons consider 20 kN as max. capacity for the whole stack. It is recommended to use 2 foldable angles and 2 angles of the rigid type for each stack.

Not shown. Suited for absorbent and non-absorbent forming faces.Solvent-based. Evaporates when applied, leaving avery thin film of release agent on the facing. Especially recommended for formwork with alkus facing (apply sparingly by using the stainless steel jet). Water hazard class 1, i.e. generally not hazardous to water. Consumption: 1 litre for approx. 50-90 m².

Not shown. To allow for an even and sparing spraying of the forming surface, suited for (5 litre) MevaTrenn and wax.

With 6 or 10 replaceable hard-metal plates and steel ledge. Wooden stick (ash-tree) with handle.

Galvanized. Is used to attach planks or cross beams to H20 beams when using slab tables.

Secures stacked panels.

Is used to close unused tie holes (AluFix, EcoAs, AluFix, AluStar and StarTec).

Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc. Length of thread 12 cm.

Galvanized. Can be used for floor slabs and slab ends up to 80 cm high. Can be inclined by up to +/- 15°. With plastic nail bar. Can be folded for transport.

Not shown. Is used to attach brace bracket 80. Double-headed. Is removed from the earth with the extractor. (to be ordered separately).

Steel, uncoated. Bottom bent by 45°. Supports DW 15, DW 20 and DW 26,5 tie rods.The tie rods are re-usable if PVC sleeves are used. The anchor support is always attached with the integrated adjusting screw.

Steel, uncoated. Admissible load: DW 15 = 180 kN, DW 20 = 320 kN. Is used for 45° anchoring in the bottom slab when using support frames. Attachment at bottom rebar.

With DW thread. DIN 18216. Connects tie rods to the anchor loops when length extension is necessary. Adm. load capacity and SW depend on nut diameter: Ø 15 mm (90 kN, SW 30), Ø 20 mm (160 kN, SW 36), Ø 26,5 mm (250 kN, SW 46).

Adjustment range 100 mm. Is used to brace upstand formwork.

Uncoated; not weldable; with DW thread; DIN 18216. To transfer the load from the support frame into the floor slab or foundation Ø in mm. Ø 15: admissible load capacity 90 kN, Ø 20: admissible load capacity 160 kN, Ø 26,5: admissible load capacity 250 kN.

Uncoated. Is used to anchor tie rods in the concrete with anchor supports.

Not shown. Measures tractive force of anchors from 250 to 400 kN. Includes compensating plate for tie rods, with 50 mm hole diameter.

Galvanized, yellow, pluggable. Is used as working and safety scaffold. Is attached to the multi-function profile and secured to the multi-function profile below with a flange screw 18. The planking can be mounted to the brackets. Working width approx. 90 or 125 cm. MEVA Guard-railing post is also required. Bracket spacing depends on type of planking (DIN 4420).

Sturdy steel construction, coated: Height 2,20 or 3,00 m. Is used to brace single-sided wall formwork up to a pouring heights of 330 cm. A spindle allows for the precise plumb-vertical positioning of the formwork.

Sturdy steel construction, coated, height 4,50 m. To brace single-sided wall formwork up to a pouring height of 5,00 m. A spindle allows to set the formwork plumb.

Not shown. Coated. Connects the support frame STB 450 with the STB-height extension 150 and the height extensions to each other.

Coated. Height 1,50 m. Extends support frame STB 450 by 1,50 m (one or several times). Pouring heights of 7,50 m (or higher) also require Triplex SB braces and base extensions. The reuqired connecting devices are included in the delivery.

Coated. Is used for the one-time or -multiple backward extension of support frame STB 450 and for the attachment of Triplex SB braces.

Coated. Supplements the support frame STB 300 for special applications, which require a detailed planning and static calculation by MEVA engineers.

Not shown. The support frame STB 450 for mobile unit is equipped with an additional steel plate so it can be distinguished from other support frames. The steel plate is in signal colour.

Coated. Links formwork in vertical position and support frames with flange screws. Allows to build transport units. Welded-in nuts guarantee a support frame spacing adapted to MEVA wall formwork systems.

Galvanized. In connection with support frames STB 300 it is used as a tie-beam to transfer the load from the support frame into the anchoring loops.

Galvanized. Garantee tensile and compression strength. Align and brace wall formwork. Foot plates and formwork-prop-connectors to be ordered separately.

Galvanized. Guarantee tensile and compression strength. With right-hand and left-hand spindle and revolving centre part. Align and brace wall formwork. Foot plates and formwork-prop-connectors to be ordered separately.

Galvanized. Is hooked into the CF-access platform and automatically secured. Can be extended with extension ladders. Safety cages are required for operational safety.

Galvanized. Is used to attach push-pull props or braces to foot plates and formwork-prop connectors.

Not shown. Galvanized. Locks the head bolt.

Galvanized. Is used to reinforce large-size units of support frames or climbing systems for transport.

Galvanized. Connects 2 scaffold tubes with Ø 48,3 mm at an angle of 90°. SW 22.

Galvanized. Connect 2 scaffold tubes with Ø 48,3 mm at any angle required.

Galvanized. Permits the attachment of scaffold tubes with Ø 48,3 mm to support frames, climbing brackets, etc.

Galvanized. Is used together with a tube connector 48 to attach scaffold tubes with Ø 48,3 mm at tube joints.

Galvanized. Is required for joint coupler 48/48 and used to reinforce the joint of 2 tubes.

Galvanized. Provides together with the base extension the required additional support for concreting heights of 7,50 m (or higher). For details see the Triplex Technical Instruction Manual.

Galvanized. Is used to attach a support frame to the tie holes of panels in horizontal position. A flange nut 100 or an articulated flange nut 15/120 is required.

Coated. Is used to form stop ends when the pouring height exceeds 4,00 m. For max. wall thickness 1,10 m. A clamping device for stop end brackets SB 110 (or a tie rod DW 15 with a length of 45 cm) is required to attach the stop end bracket SB 110 to the support frame.

Coated. Is used to connect the stop end bracket SB 110 to the support frame. A flange nut 100 or an articulated flange nut 15/120 is also required.

Galvanized. Are used to brace panel joints for crane ganging, bridge problem areas, brace compensation areas and build stop ends with stop end fixtures. Are attached to the formwork with flange screws.

Galvanized. DW thread Ø 15 mm. Is used to attach accessories to the multi-function profiles of the panels, e.g. alignment rails, cross braces, cross beams 300, formwork-prop connectors, etc.

Coated. Supports the inside corner area of single-sided wall formwork. Dimensions 137 x 137 cm. Welded-in DW-threaded nuts to attach 2 or 3 support frames STB 300 or STB 450. Flange screws are required to attach the cross brace to the formwork and the support frame to the cross brace.

Galvanized. Connects 2 scaffold tubes with 48,3 mm Ø at any angle.

Galvanized. Is plugged into the walkway bracket.

Galvanized. With head bolt 16/90 and cotter pin 4. Is used to attach push-pull props to vertical or horizontal panel joints A Combi-lock with coupling is also required. Typical application in folding shaft formwork.

Galvanized. Is used to connect braces, brace frames and push-pull props (max. Ø 48,3 mm) to the multi-function profile with a flange screw 18. Delivery includes head bolt 16/90 and cotter pin 4.

Galvanized. Locks the head bolt.

Galvanized. Is plugged into the walkway bracket.

Galvanized. With manifold to attach it to the walkway bracket, designed with tube Ø 48 mm to attach tube couplers.

Steel spiral bead, 10 cm long, with styropore core. Is used to attach formwork equipment with tie rods DW 15, e.g. when adjusting the equipment when using push-pull props or the like. Remove the styropore with a 14 mm drill.

Is used as a plastic sleeve for a tie rod that is to be recovered and re-used. 2 m long.

Hard foam, 10 cm long, 45° end piece. For DW 15 and DW 20. Is plugged onto the DW tie rod or on a plastic sleeve for one-sided anchoring of support frames STB. Hole depth 5 cm.

Steel spiral bead, 10 cm long, with styropore core. Is used to attach formwork equipment with tie rods DW 15, e.g. when adjusting the equipment when using push-pull props or the like. Remove the styropore with a 14 mm drill.

Galvanized. Internal Ø 70 cm. Protects workers when ascending and descending the ladder. The safety cages are attached to the (extension) ladders with the integrated hammerhead screws.

Steel, uncoated. Bottom bent by 45°. Supports DW 15, DW 20 and DW 26,5 tie rods.The tie rods are re-usable if PVC sleeves are used. The anchor support is always attached with the integrated adjusting screw.

Forged; with DW thread; DIN 18216. To tie the anchors in the bottom slab and at the support frame; is used with a counter plate to increase the pull-out resistance. Admissible load in kN and SW in mm. Ø 15 mm (90 kN, SW 30), Ø 20 mm (160 kN, SW 36), Ø 26,5 mm (250 kN, SW 46).

Steel, uncoated. Admissible load: DW 15 = 90 kN, DW 20 = 160 kN, DW 26 = 250 kN. Is used for 45° anchoring in the bottom slab when using support frames. Attachment at bottom rebar.

Galvanized steel frame. Hatch made from checker plate. Cataphoretic coating; max. opening 88°, self-closing.

Steel, uncoated. Admissible load: DW 15 = 180 kN, DW 20 = 320 kN. Is used for 45° anchoring in the bottom slab when using support frames. Attachment at bottom rebar.

Not shown. For DW 15, DW 20 and DW 26,5. Is used to loosen and unscrew recoverable tie rods.

Adjustment range 100 mm. Is used to brace upstand formwork.

Forged, galvanized. DIN 18216. DW thread Ø 15 mm (20 mm). Plate Ø 120 mm (140 mm), max. inclination 10°, SW 27 (36). Max. load capacity 90 kN (160 kN).

Forged; galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 100 mm, SW 27. Max. load capacity 90 kN.

Inset yellow chromated; spanner width 36 mm. To tighten and loosen articulated flange nuts 20/140.

Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc. Length of thread 18 cm or 27 cm.