Enkelzijdige wand:
Mammut 350

De Mammut 350 wandbekisting voor stortwerk dat een groot oppervlak beslaat. De Mammut 350 wandbekisting voor stortwerk dat een groot oppervlak beslaat. Mammut 350 draagt over het hele oppervlak 100 kN/m² en is met zijn symmetrische ankerpunten en de massieve kunststof bekistingsplaat alkus uitermate geschikt voor zichtbetonwerk.

Verder onderaan op deze pagina vindt u de artikelen die u nodig heeft als u een wand met Mammut 350 wilt bekisten. Denk er aan dat het aantal artikelen voor elk bouwproject kan verschillen. Gebruik het formulier en neem even contact met ons op als u exact wilt weten hoeveel onderdelen u nodig heeft.

Op de productpagina vindt u alles over onze sterkste wandbekisting Mammut 350 .

Downloads voor Mammut 350 wandbekisting

Contactformulier

 
 
 

Of neem rechtstreeks contact met ons op.

 

Artikellijst

 
 
Bekisting
Verankering
Ondersteuning
Sicherheit
 
 
  • RS-assembly lock

    Galvanized, to tightly connect and align Radius panels. Clamping length is 119 to 205 mm for stepless compensation. 2... 

  • Combi-lock with coupling

    Galvanized; to attach the push-pull props at the panel joint of the wall formwork AluStar, StarTec, Mammut, Mammut 350 and... 

  • M-Cross stiffener 44

    Galvanized. In connection with support frames STB 300 it is used as a tie-beam to transfer the load from the support frame... 

  • Cross beam 300

    Coated. Links formwork in vertical position and support frames with flange screws. Allows to build transport units.... 

  • Transport angle 12

    Is used to stack and transport 5 to 12 frame formwork panels with a construction height of 12 cm and 12 cm hole distance.... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

 
 
  • Tie rod DW

    Uncoated; not weldable; with DW thread; DIN 18216. To transfer the load from the support frame into the floor slab or... 

  • Brace bracket 80

    Galvanized. Can be used for floor slabs and slab ends up to 80 cm high. Can be inclined by up to +/- 15°. With plastic nail... 

  • Flange screw 12

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • Double-headed ground nail 25/280

    Not shown. Is used to attach brace bracket 80. Double-headed. Is removed from the earth with the extractor. (to be ordered... 

  • Extractor for double-headed ground nail

    Not shown. Is used to remove the ground nail from the earth together with a lever rod (not supplied).  

  • Anchor support DW 15 - DW 26,5

    Steel, uncoated. Bottom bent by 45°. Supports DW 15, DW 20 and DW 26,5 tie rods.The tie rods are re-usable if PVC sleeves... 

  • Double anchor DW

    Steel, uncoated. Admissible load: DW 15 = 180 kN, DW 20 = 320 kN. Is used for 45° anchoring in the bottom slab when using... 

  • Coupling nut

    With DW thread. DIN 18216. Connects tie rods to the anchor loops when length extension is necessary. Adm. load capacity and... 

  • Upstand bracket

    Adjustment range 100 mm. Is used to brace upstand formwork. 

  • Fix anchor

    Uncoated. Is used to anchor tie rods in the concrete with anchor supports. 

  • Pressure gauge

    Not shown. Measures tractive force of anchors from 250 to 400 kN. Includes compensating plate for tie rods, with 50 mm hole... 

 
 
  • Walkway bracket

    Galvanized, yellow, pluggable. Is used as working and safety scaffold. Is attached to the multi-function profile and secured... 

  • Guard-railing post

    Galvanized. Is plugged into the walkway bracket. 

  • Push-pull prop R

    Galvanized. Garantee tensile and compression strength. Align and brace wall formwork. Foot plates and... 

  • Braces SRL

    Galvanized. Guarantee tensile and compression strength. With right-hand and left-hand spindle and revolving centre part.... 

  • Universal joint connector 76/135

    Galvanized. With head bolt 16/90 and cotter pin 4. Is used to attach push-pull props to vertical or horizontal panel joints... 

  • Ladder

    Galvanized. Is hooked into the CF-access platform and automatically secured. Can be extended with extension ladders. Safety... 

  • Formwork-prop connector

    Galvanized. Is used to connect braces, brace frames and push-pull props (max. Ø 48,3 mm) to the multi-function profile with... 

  • Cotter pin 4

    Galvanized. Locks the head bolt. 

  • Head bolt 16/90

    Galvanized. Is used to attach push-pull props or braces to foot plates and formwork-prop connectors. 

  • Cotter pin 4

    Not shown. Galvanized. Locks the head bolt. 

  • Support frame STB 300

    Sturdy steel construction, coated: Height 2,20 or 3,00 m. Is used to brace single-sided wall formwork up to a pouring... 

  • Base extension 300/200

    Coated. Supplements the support frame STB 300 for special applications, which require a detailed planning and static... 

  • Support frame STB 450

    Sturdy steel construction, coated, height 4,50 m. To brace single-sided wall formwork up to a pouring height of 5,00 m. A... 

  • Support frame STB 450 for mobile unit

    Not shown. The support frame STB 450 for mobile unit is equipped with an additional steel plate so it can be distinguished... 

  • Height extension connector STB 450

    Not shown. Coated. Connects the support frame STB 450 with the STB-height extension 150 and the height extensions to each... 

  • STB-height extension 150

    Coated. Height 1,50 m. Extends support frame STB 450 by 1,50 m (one or several times). Pouring heights of 7,50 m (or higher)... 

  • STB-base extension

    Coated. Is used for the one-time or -multiple backward extension of support frame STB 450 and for the attachment of Triplex... 

  • Scaffold tube

    Galvanized. Is used to reinforce large-size units of support frames or climbing systems for transport.  

  • Rigid coupler 48/48

    Galvanized. Connects 2 scaffold tubes with Ø 48,3 mm at an angle of 90°. SW 22. 

  • Joint coupler 48/48 SW 22

    Galvanized. Is used together with a tube connector 48 to attach scaffold tubes with Ø 48,3 mm at tube joints. 

  • Tube connector 48

    Galvanized. Is required for joint coupler 48/48 and used to reinforce the joint of 2 tubes. 

  • Triplex SB

    Galvanized. Provides together with the base extension the required additional support for concreting heights of 7,50 m (or... 

  • Fixing screw 35/DW15

    Galvanized. Is used to attach a support frame to the tie holes of panels in horizontal position. A flange nut 100 or an... 

  • Stop end bracket SB 110

    Coated. Is used to form stop ends when the pouring height exceeds 4,00 m. For max. wall thickness 1,10 m. A clamping device... 

  • Clamping device for stop end bracket SB 110

    Coated. Is used to connect the stop end bracket SB 110 to the support frame. A flange nut 100 or an articulated flange nut... 

  • M alignment rail

    Galvanized. Are used to brace panel joints for crane ganging, bridge problem areas, brace compensation areas and build stop... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories to the multi-function profiles of the panels, e.g. alignment... 

  • Cross brace STB

    Coated. Supports the inside corner area of single-sided wall formwork. Dimensions 137 x 137 cm. Welded-in DW-threaded nuts... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • Cross beam 300

    Coated. Links formwork in vertical position and support frames with flange screws. Allows to build transport units.... 

  • M-Cross stiffener 44

    Galvanized. In connection with support frames STB 300 it is used as a tie-beam to transfer the load from the support frame... 

  • Swivel-joint coupler 48/48

    Galvanized. Connect 2 scaffold tubes with Ø 48,3 mm at any angle required. 

  • Bolt-on coupler 48/M14

    Galvanized. Permits the attachment of scaffold tubes with Ø 48,3 mm to support frames, climbing brackets, etc. 

Vanaf een storthoogte van 2 m dient er altijd een een vierdelige zijdelingse bescherming aan het stortplatform te worden aangebracht.

Met de MEVA veiligheidssysteem kunt u uw bouwterrein modulair en individueel beveiligen. Kijk voor meer informatie op de Veiligheidssystemen pagina en neem voor voor advies contact op met MEVA.

  • Guard-railing post

    Galvanized. Is plugged into the walkway bracket. 

  • Guard-railing post 48

    Galvanized. With manifold to attach it to the walkway bracket, designed with tube Ø 48 mm to attach tube couplers. 

  • Spiral anchor DW 15/100

    Steel spiral bead, 10 cm long, with styropore core. Is used to attach formwork equipment with tie rods DW 15, e.g. when... 

  • Scaffold tube

    Galvanized. Is used as hand-rail / mid-rail in combination with guard-railing post 48. 

  • Plastic tube

    Is used as a plastic sleeve for a tie rod that is to be recovered and re-used. 2 m long.  

  • Planing cap DW

    Hard foam, 10 cm long, 45° end piece. For DW 15 and DW 20. Is plugged onto the DW tie rod or on a plastic sleeve for... 

  • Spiral anchor DW 15/100

    Steel spiral bead, 10 cm long, with styropore core. Is used to attach formwork equipment with tie rods DW 15, e.g. when... 

  • Safety cage

    Galvanized. Internal Ø 70 cm. Protects workers when ascending and descending the ladder. The safety cages are attached to... 

  • Anchor support DW 15 - DW 26,5

    Steel, uncoated. Bottom bent by 45°. Supports DW 15, DW 20 and DW 26,5 tie rods.The tie rods are re-usable if PVC sleeves... 

  • Hexagonal nut

    Forged; with DW thread; DIN 18216. To tie the anchors in the bottom slab and at the support frame; is used with a counter... 

  • Single anchor DW

    Steel, uncoated. Admissible load: DW 15 = 90 kN, DW 20 = 160 kN, DW 26 = 250 kN. Is used for 45° anchoring in the bottom... 

  • Access hatch KLK

    Galvanized steel frame. Hatch made from checker plate. Cataphoretic coating; max. opening 88°, self-closing. 

  • Double anchor DW

    Steel, uncoated. Admissible load: DW 15 = 180 kN, DW 20 = 320 kN. Is used for 45° anchoring in the bottom slab when using... 

  • Upstand bracket

    Adjustment range 100 mm. Is used to brace upstand formwork. 

  • Articulated flange nut

    Forged, galvanized. DIN 18216. DW thread Ø 15 mm (20 mm). Plate Ø 120 mm (140 mm), max. inclination 10°, SW 27 (36). Max.... 

  • Flange nut 100

    Forged; galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 100 mm, SW 27. Max. load capacity 90 kN. 

  • Spanner SW 36

    Inset yellow chromated; spanner width 36 mm. To tighten and loosen articulated flange nuts 20/140. 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc....